How to apply Industtrial epoxy microcement on indoor walls and floors
Industtrial epoxy microcement has a high adhesion to mineral substrates, even on
direct tile. It is a decorative continuous coating highly recommended for decorating interior
walls and floors, especially in areas with high wear such as garages, industrial buildings,
gallery floors, stores, waiting rooms, corridors or offices.
In general, Industtrial is an epoxy microcement ideal for those continuous pavements exposed to
high pedestrian traffic.
Below, we explain the step-by-step application of Industtrial epoxy microcement on interior
floors and walls.
Step 3. Pigment component A of the INDUSTTRIAL XL epoxy microcement.
Pigment component A of INDUSTTRIAL XL epoxy microcement with the
ARCOCEM® PLUS color toner chosen from the INDUSTRIAL color chart.
Step 4. Mix component A and component B of INDUSTRIAL XL .
Once component A of INDUSTTRIAL XL epoxy microcement has been pigmented, add
component B and mix (see exact proportions in the technical data sheet). If
Comp.A is not pigmented, the A+B mixture can be pigmented.
Step 5. Apply two coats of Industtrial XL epoxy microcement
Apply with a trowel two coats of INDUSTTRIAL XL epoxy microcement
preparation. Allow to dry between 8 and 12 hours between coats. The time
depends on the temperature and humidity (see technical data sheet). Sand
after each coat with 220 grit sandpaper.
Step 6. Apply a coat of Industtrial Medium epoxy microcement
*Repeat steps 3 and 4 for INDUSTTRIAL MEDIO.
To finish decorating the interior floor, apply a coat of INDUSTTRIAL MEDIUM
epoxy microcement finish. Allow to dry at least 48 hours
Step 7. Sealing.
To protect the floor or interior epoxy flooring, apply a sealer from the
Topsealer® family. We recommend two coats of TOPSEALER® WT DRAGON (12h
between coats) or TOPSEALER® WT ONE COAT (8h between coats).
Step 1. Cleaning and preparation of the substrate.
Make sure the substrate is dry, clean, free of dust, grease or dirt. If the
walls are varnished or painted, remove the previous coating.
Step 2. Priming.
On mineral or cementitious surfaces it is highly recommended to use PRIMACEM®
family. If there is moisture, use PRIMAPOX® 100 BARRIER.
Step 3. Color component A of the Industtrial Base epoxy microcement.
Color component A of the INDUSTTRIAL BASE epoxy microcement with the
ARCOCEM® PLUS color toner chosen from the INDUSTTRIAL color chart.
Step 4. Join component A with component B of INDUSTTRIAL BASE.
After pigmenting component A of INDUSTTRIAL BASE epoxy microcement, add
component B and mix the two components (see proportions in the technical
data sheet). The mixture A+B can also be pigmented.
Step 5. Two coats of Industtrial Base epoxy microcement.
For interior epoxy walls, apply two coats of INDUSTRIAL BASE epoxy
microcement with a trowel. Allow to dry approximately 8 to 12 hours between
coats. The exact time will vary depending on the degree of temperature and
humidity (see technical data sheet). Sand with 220 grit sandpaper after each
coat.
Step 6. One coat of Industtrial Smooth epoxy microcement
*Repeat steps 3 and 4 for INDUSTTRIAL LISO. To finish the decoration of the
interior wall, apply a coat of epoxy microcement finishing INDUSTTRIAL LISO.
Allow to dry at least 48 hours before sealing and sand with 400 grit
sandpaper.
Step 7. Sealing .
Protect the interior epoxy wall. Any of our Topsealer® varnishes can be
applied. We recommend two coats of TOPSEALER® WT DRAGON (leaving 12h between
coats) or TOPSEALER® WT ONE COAT (leaving 8h between coats).