menu
Cerrar

Epoxy microcement for interior floors and walls | Industtrial

Industtrial is our exclusive product line of epoxy microcement (arid + epoxy resin). A decorative continuous coating especially for interior walls and floors. In this product we have combined the excellent performance of our microcements with the extra hardness provided by epoxy resins.

The result is a continuous coating of very high results, especially for continuous interior pavements and floors. An epoxy microcement with excellent workability and unbeatable resistance to abrasion and pedestrian traffic.

In addition, our water-based epoxy microcement Industtrial stands out for its very natural mineral finish and for its superior impermeability compared to conventional microcement systems.

Industtrial is available in 16 colours and 4 granulometries: Industtrial XL, Industtrial Base, Industtrial Medio and Industtrial Liso.

Due to the finishes offered by this epoxy microcement, we recommend using Industtrial XL and Industtrial Medio for floors and Industtrial Base and Industtrial Liso for walls. However, all four granulometries are suitable for both floors and interior walls.

Why choosing Industtrial epoxy microcement?

In addition to the resistance, hardness and functionality offered by Industtrial, it is an epoxy microcement that provides the applicator with significant benefits compared to other similar products on the market.

Industtrial stands out for its high covering power. A material that can coat the substrate up to 3 and 4 times more and better than its counterparts.

In this sense, with Industtrial it is only necessary to apply a finishing coat. This is an added value compared to other products that require two coats to complete the decoration of the substrate.

It is also an epoxy microcement with outstanding workability. It is a product that can be reworked and, furthermore, in the event of making a mistake in the application, it is possible to correct it instantly. It is therefore not necessary to re-coat the entire substrate, only the affected area.

Industtrial allows the most diverse and special designs to be created. Different pigments can be combined for the different layers, creating an even more attractive finish.

Another of the main advantages of this epoxy microcement over the competition is that if imperfections are left on the substrate when sanded, they do not bleach. This is a problem that many products do have.

In the case of using Industtrial on walls, the product does not sag. Excellent adhesion without the need to add additives, as is the case with other products.

Industtrial provides greater hardness and impermeability than conventional microcements. An epoxy microcement capable of resisting abrasion, pedestrian traffic and chemical agents such as ammonia, soft drinks or coffee.

Logo Industtrial XL

Industtrial XL epoxy microcement for floor and paving preparation

Industtrial XL is our epoxy microcement for the preparation of epoxy floors and paving. After applying this decorative continuous coating to any interior floor or screed, one coat of Industtrial Medium should be applied to complete the epoxy system.

Although Industtrial XL is intended for interior epoxy floor and wall coverings, it can also be used on walls if a specific finish is required.

Download here the Industtrial XL technical data sheet.

Types of epoxy microcement for floor and paving preparation Industtrial XL

Industtrial  XL 18 kG
Industtrial XL 18 Kg
Industtrial  XL 4,5 kg
Industtrial XL 4,5 Kg

Industtrial XL floor preparation epoxy microcement characteristics

icono ph
pH of Component A

9,5 ± 1

Densidad aparente
Density

1,65 ± 0,02 g/mL (Component A)
At 25ºC 1,16 g/mL (Component B)
0,98 ± 0,02 g/cm³ (Component C)

icon
Total cure

7- 14 days

icono dureza
Shore hardness

80-87

Consumption

The consumption of Industtrial XL epoxy microcement for interior floors and paving is: 1.40 Kg/m2 (1 coat).

Packaging

Industtrial XL epoxy microcement for preparation of interior floors and pavements is available in two types of packaging. 4,5 Kg Comp. A + 0,5 Kg Comp. B + 35g Comp. C to pigment 100g of ARCOCEM WT PLUS and packages of 18 Kg Comp. A + 2 Kg Comp.B + 140g Comp. C to pigment 400g of ARCOCEM WT PLUS.

Logo Industtrial Base

Industtrial Base epoxy microcement for wall preparation

Industtrial Base is our epoxy microcement preparation coating for interior wall coverings. After applying this decorative continuous coating for walls, one coat of Industtrial Liso must be applied to complete the epoxy system.

Download here the Industtrial Base technical data sheet

Types of epoxy microcement for wall preparation Industtrial Base

Industtrial  Base 18 kG
Industtrial Base 18 Kg
Industtrial  Base 4,5 kg
Industtrial Base 4,5 Kg

Industtrial Base epoxy microcement wall preparation characteristics

icono ph
pH of Component A

9,5 ± 1

Densidad aparente
Density

1,65 ± 0,02 g/mL (Component A)
At 25ºC 1,16 g/mL (Component B)
0,98 ± 0,02 g/cm³ (Component C)

icon
Total cure

7- 14 days

icono dureza
Shore hardness

80-87

Consumption

The consumption of Industtrial Base epoxy microcement for preparing interior walls is: 1.20 Kg/m2 (1 coat).

Packaging

The epoxy microcement preparation for interior walls Industtrial Base is available in two packs. To pigment 100g of ARCOCEM WT PLUS: 4.5 Kg Comp. A + 0.5 Kg Comp. B + 35g Comp. C; and to pigment 400g of ARCOCEM WT PLUS: 18 Kg Comp. A + 2 Kg Comp.B + 140g Comp. C.

Logo Industtrial Medio

Industtrial Medio epoxy microcement for finishing floors and pavements

Industtrial Medio is our epoxy microcement for finishing epoxy floors and paving in interior spaces. To obtain this decorative continuous flooring, it is necessary to apply two coats of Industtrial XL beforehand.

As with Industtrial XL, although Industtrial Medio is specially designed for epoxy floors and interior flooring, it can also be applied on walls if a different finish is required.

Download here the Industtrial Medio data sheet

Types of epoxy microcement for finishing floors and pavements Industtrial Medio

Industtrial  Medio 18 kG
Industtrial Medio 18 Kg
Industtrial  Medio 4,5 kg
Industtrial Medio 4,5 Kg

Characteristics of microcement epoxy floor finish Industtrial Medio

icono ph
pH of Component A

9,5 ± 1

Densidad aparente
Density

1,65 ± 0,02 g/mL (Component A)
At 25ºC 1,16 g/mL (Component B)
0,98 ± 0,02 g/cm³ (Component C)

icon
Total cure

7- 14 days

icono dureza
Shore hardness

80-87

Consumption

The consumption of Industtrial Medio epoxy microcement for interior floors and paving is: 0.70 Kg/m2 (1 coat).

Packaging

The finishing epoxy microcement for interior flooring and floors Industtrial Medio is also available in two packs. On one side packs of 4,5 Kg Comp. A + 0,5 Kg Comp. B + 35g Comp. C (to pigment 100g of ARCOCEM WT PLUS), and on the other side packs of 18 Kg Comp. A + 2 Kg Comp. B + 140g Comp. C (to pigment 400g of ARCOCEM WT PLUS).

Logo Industtrial liso

Industtrial Liso epoxy microcement for wall finishing

Industtrial Liso is our epoxy microcement ideal for coating interior walls. Two coats of Industtrial Base must be applied beforehand.

Download here the Industtrial Liso technical data sheet

Types of epoxy microcement for wall finishing Industtrial Liso

Industtrial  Liso 18 kG
Industtrial Liso 18 Kg
Industtrial  Liso 4,5 kg
Industtrial Liso 4,5 Kg

Characteristics of microcement epoxy wall finishing Industtrial Liso

icono ph
pH of Component A

9,5 ± 1

Densidad aparente
Density

1,65 ± 0,02 g/mL (Component A)
At 25ºC 1,16 g/mL (Component B)
0,98 ± 0,02 g/cm³ (Component C)

icon
Total cure

7- 14 days

icono dureza
Shore hardness

80-87

Consumption

The consumption of Industtrial Liso epoxy microcement for interior walls is: 0.55 Kg/m2 (1 coat).

Packaging

The finishing epoxy microcement for interior walls Industtrial Liso is available in the same packs as the other granulometries. 4,5 Kg Comp. A + 0,5 Kg Comp. B + 35g Comp. C (to colour 100g of ARCOCEM WT PLUS) and 18 Kg Comp. A + 2 Kg Comp.B + 140g Comp. C (to colour 400g of ARCOCEM WT PLUS).

Components B and C of the Industtrial epoxy microcement

Resina Epoxy

BPA Epoxy Resin

BPA epoxy resin and 100% solids. This hardener, component B of Industtrial , is responsible for the increased durability, waterproofing and abrasion resistance of the product.

Viscosity: 8 - 10 Pa-s

Flash point: 266ºC -

Density at 25ºC: 1,16 g/mL

Packaging: 0.5 kg and 2 kg containers.

See technical data sheet

Epoxy 100 Accelerator: accelerator for epoxy hardeners

Low viscosity accelerating reagent for epoxy hardeners and Industtrial's C component. Solvent-free product that does not require dilution. Accelerates the drying of the epoxy resin to the touch, the minimum application temperature and reduces the pot-life of the mixture.

Density: 0.98 ± 0.02 g/cm³.

Flash-Point: 149ºC

Amine Index: min 608 mgKOH/g

pH: 11,3

Packaging: 35g and 140g packs.

See technical data sheet
Resina Epoxy

How to apply Industtrial epoxy microcement on indoor walls and floors

Industtrial epoxy microcement has a high adhesion to mineral substrates, even on direct tile. It is a decorative continuous coating highly recommended for decorating interior walls and floors, especially in areas with high wear such as garages, industrial buildings, gallery floors, stores, waiting rooms, corridors or offices.

In general, Industtrial is an epoxy microcement ideal for those continuous pavements exposed to high pedestrian traffic.

Below, we explain the step-by-step application of Industtrial epoxy microcement on interior floors and walls.

+ Application of Industtrial epoxy microcement on interior floors and pavements

Step 1. Cleaning and preparation of the substrate.

Ensure that the substrate is dry, clean, free of dust, grease or dirt. In case the floor or indoor flooring is varnished or painted, remove the previous coating.

icon
paso 1 Industtrial

Step 2. Priming..

On mineral or cementitious surfaces, it is highly recommended to use the PRIMAPOX® or PRIMACEM® family. If there is moisture, use PRIMAPOX® 100 BARRIER.

icon
Paso 2 Industtrial

Step 3. Add Epoxy 100 Accelerator to component A of Industtrial XL.

Homogenise component A of INDUSTTRIAL XL epoxy microcement. Then add the Epoxy 100 Accelerator accelerating reagent. Stir until a completely homogeneous mixture is obtained.

icon
Paso 3 Industtrial

Step 4. Pigment component A of the INDUSTTRIAL XL epoxy microcement.

Pigment component A of the INDUSTTRIAL XL epoxy microcement with the ARCOCEM® PLUS colour toner chosen from the INDUSTTRIAL colour chart.

icon
paso 4 Industtrial

Step 5. Mix INDUSTTRIAL XL component A and component B.

Once component A of the INDUSTTRIAL XL epoxy microcement has been pigmented, add component B and mix the two components (see the exact proportions in the technical data sheet).

icon
paso 4 Industtrial

Step 6. Apply two coats of Industtrial XL epoxy microcement.

Apply two coats of INDUSTTRIAL XL preparation epoxy microcement with a trowel. Allow to dry for 8 to 12 hours between coats. The time depends on temperature and humidity (see technical data sheet). Sand after each coat with 220 grit sandpaper.

icon
Paso 6 Industtrial

Step 7. Apply a coat of epoxy microcement Industtrial Medio.

*Repeat steps 3, 4 and 5 for INDUSTTRIAL MEDIO.
To finish decorating the interior floor, apply a coat of INDUSTTRIAL MEDIO epoxy microcement finish. Allow to dry for at least 48 hours before sealing. Sand with 400 grit sandpaper.

icon
Paso 6 Industtrial

Step 8. Sealing.

To protect the floor or interior epoxy floor, apply three coats of TOPSEALER® WT ALL IN ONE varnish (3 hours drying time between coats) or two coats of TOPSEALER® WT ONE COAT varnish (24 hours between coats).

icon
Paso 6 Industtrial

+ Industtrial epoxy microcement application on interior walls

Step 1. Cleaning and preparation of the substrate.

Make sure the substrate is dry, clean, free of dust, grease or dirt. If the walls are varnished or painted, remove the previous coating.

icon
paso 1 Industtrial

Step 2. Priming.

On mineral or cementitious surfaces it is highly recommended to use the PRIMAPOX® or PRIMACEM® family. If there is moisture, use PRIMAPOX® 100 BARRIER.

icon
Paso 2 Industtrial

Step 3. Add Epoxy 100 Accelerator to component A of Industtrial Base.

Unify component A of INDUSTTRIAL BASE epoxy microcement. Then add the PRIMAPOX® 100 Accelerator accelerating reagent. Stir until a homogeneous mixture is obtained.

icon
Paso 3 Industtrial

Step 4. Colour component A of the epoxy microcement INDUSTRIAL BASE.

Colour component A of the INDUSTTRIAL BASE epoxy microcement with the ARCOCEM® PLUS colour toner chosen from the INDUSTTRIAL colour chart.

icon
paso 4 Industtrial

Step 5. Join component A with component B of INDUSTTRIAL BASE.

After pigmenting component A of the INDUSTTRIAL BASE epoxy microcement, add component B and mix the two components (see proportions in the technical data sheet).

icon
paso 4 Industtrial

Step 6. Two coats of Industtrial Base epoxy microcement.

For interior epoxy walls, apply two coats of INDUSTTRIAL BASE epoxy microcement with a trowel. Allow to dry for 8 to 12 hours between coats. The exact time will depend on the degree of temperature and humidity (see technical data sheet). Sand with 220 grit sandpaper after each coat.

icon
Paso 6 Industtrial

Step 7. One coat of Industtrial Liso epoxy microcement.

*Repeat steps 3, 4 and 5 for INDUSTTRIAL LISO.
To finish the decoration of the interior wall, apply a coat of INDUSTTRIAL LISO epoxy microcement. Allow to dry for at least 48 hours before sealing and sand with 400 grit sandpaper.

icon
Paso 6 Industtrial

Step 8. Sealing.

Protect the interior epoxy wall. Three coats of our TOPSEALER® WT ALL IN ONE varnish can be applied (allow 3 hours drying time between coats) or two coats of TOPSEALER® WT ONE COAT varnish (allow 24 hours drying time between coats).

icon
Paso 6 Industtrial

Colours of Industtrial epoxy microcement

Industtrial epoxy microcement is available in 16 colours, offering a multitude of decorative possibilities as a continuous coating for interior epoxy floors and walls. Epoxy resin colours that offer the professional uniform finishes of great beauty and among which stand out those pearly and pearlescent shades that bring elegance and sophistication to the interior design of any room.

The versatility of Industtrial epoxy microcement pigments not only brings distinction and attractiveness to interior epoxy floors. They are also colours that allow the epoxy resin to reach its maximum performance, while boosting the colour and shine of the flooring. A combination that prolongs the useful life of the floors, making them much more durable over time.

Pannacotta Taupe Linen Hazelnut
Wicker Koala Walnut Anthracite
Shadow Black Pure Black Gem Grey Ultimate Grey
Moon Universe Nebula Patagonia
microcementos
microcementos

Frequently asked questions Industtrial epoxy microcement

We do not recommend using Industtrial epoxy microcement outdoors. This is because the epoxy resin may yellow when exposed to the sun's rays.

Therefore, we recommend using Industtrial epoxy microcement as a decorative and functional finish on floors and walls in interior spaces.

Industtrial epoxy microcement is formulated so that it is not necessary to use mesh, as it is a product that is applied in very thin layers that favour optimum drying. If mesh were used, the layers of product would be much thicker and there would be a risk of cracking.

As with other microcement systems, it is essential to prepare the substrate properly to ensure a good decorative coating. In this sense, the substrate must be well consolidated, have a good planimetry and be free of damp (if this is not the case, it will be necessary to remedy it).

In the case of Industtrial epoxy microcement, the Primapox or Primacem family can be used as a primer. The choice of one or the other will depend on the substrate on which Industtrial is to be applied.

Yes, Primacem ABS (absorbent surfaces) or Primacem Plus (non-absorbent surfaces) can be used without any problem as a primer for Industtrial epoxy microcement. However, to ensure high performance, we recommend using Primapox for a complete epoxy system.

Although our Industtrial epoxy microcement guarantees superior resistance to other systems, including greater impermeability to running water, it is necessary to seal it. With this added protection, Industtrial's durability increases exponentially.

Depending on the finish that each professional is looking for, as well as the features required by the use to which it is going to be applied, Industtrial epoxy microcement can be sealed with different varnishes. Mainly with our water-based varnishes Topsealer WT One Coat and Topsealer WT All in One, as shown in the step-by-step application of the product.

However, to protect the Industtrial epoxy microcement, there is also the possibility of using our solvent-based Topsealer DSV and our 100% solids epoxy varnish Coverpox.

Industtiral epoxy microcement is composed of aggregates, without the need for cement, as is the case with our ready to use microcement Efectto Quartz. For this reason, the application of the Presealer can be avoided and the step-by-step time is reduced.

We have developed a total of 16 colours for Industtrial epoxy microcement, which are the samples shown above. However, if a customer would like to pigment the product with another colour, they can easily do so using our ARCOCEM BASIC.

Whenever we talk about interior spaces, Industtrial epoxy microcement can be used on walls and ceilings. Although it is true that due to its resistance to wear and tear and traffic above all, it is more suitable for use on floors.

No. Industtrial epoxy microcement cannot be applied on façades. As we have already explained, it is not recommended to use this product outdoors due to the real possibility of yellowing of the epoxy resin.

Industtrial epoxy microcement fits perfectly in interior areas exposed to high traffic such as offices, shopping centres, warehouses, etc. Spaces that require more industrial resistance.

Beyond its hardness and resistance, Industtrial epoxy microcement is characterised by its versatility. So yes, if the applicator wishes to achieve a water effect, it can be achieved.

To apply our Industtrial epoxy microcement on tiles, the first thing to do is to fill the joints with Primacem® Joint. A filler and smoothing putty which purpose is to prevent the tracing from being noticed after coating the surface with microcement.

The substrate should then be primed with two coats of our Primacem® Plus primer for non-absorbent surfaces. Primapox® Barrier epoxy primer could also be used, but we only recommend it when moisture may damage the substrate.

The A component of Industtrial epoxy microcement is the only one that is pigmented. Depending on the colour chosen, the proportions of the mixtures will be different. Component A can be pigmented in advance and left in stock until the product is applied. In this way, distributors have the possibility to sell the pigmented product directly. Any pigment that may remain in the bottle can be collected with a little water.

In addition, the versatility of Industtrial allows you to play with the different colours available to achieve a more natural finish if possible. In other words, the base layer can be pigmented with one colour and the top layer with a different one to create a very attractive visual contrast. As for the guarantee of the material, it is one year.

Once component A has been mixed with component B, water cannot be added as it repels water. In the case of wanting to add water, it will have to be done in component A before mixing it with component B.

Industtrial is an epoxy microcement that is designed with a texture suitable for its application, so adding water is not necessary. It is important to note that it is not a product compatible with the addition of resins.

Epoxy 100 Accelerator is a curing Accelerator which, as the name suggests, is intended to accelerate and reduce the drying time of the product. If it is not incorporated in component A of the Industtrial epoxy microcement, the drying times would be very long.

It is absolutely not recommended to add Epoxy 100 Accelerator to component B of Industtrial epoxy microcement because it would cause a reaction and harden the product. Therefore it could not be applied.

We do not recommend this, because Industtrial two-component could diminish its excellent performance.